Welcome,
Guest
. Please
login
or
register
.
August 22, 2008, 12:30:30 AM
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
The BigBlockDart Message Board
Technical
Engine, Drivetrain
Are these easy to get???
Pages:
[
1
]
Author
Topic: Are these easy to get??? (Read 324 times)
DART VADER
BBD God
Offline
Posts: 2040
BigBlockDart.Com
Are these easy to get???
«
on:
February 06, 2006, 08:14:07 PM »
I am putting a new waterpump in the Satellite. The hose fittings on the old one are in sad condition. Where can I get new ones?
Logged
tried and true
GON_RACIN
Sr. Member
Offline
Posts: 842
Happiness is a warm gun.
Re: Are these easy to get???
«
Reply #1 on:
February 06, 2006, 08:42:09 PM »
most part stores carry them, often they keep them behind the counter in little bins. Sometimes the old ones can be a serious pain to remove
Logged
SATELLITESIVIG
Full Member
Offline
Posts: 184
BigBlockDart.Com
Re: Are these easy to get???
«
Reply #2 on:
February 06, 2006, 08:49:23 PM »
small block or bigblock? napa will carry the screw-in fittings for the bigblock under there 600 series book.(same book they list clutch forks, wheel studs, heater cores, etc.)
Logged
best et to date 9.20@148
DART VADER
BBD God
Offline
Posts: 2040
BigBlockDart.Com
Re: Are these easy to get???
«
Reply #3 on:
February 06, 2006, 08:59:34 PM »
Small block. It's a 318. The old ones are so rusted, I would rather just put new ones on.
Logged
tried and true
sr71mopar
BBD God
Offline
Posts: 1221
Santa Rosa, CA.
Re: Are these easy to get???
«
Reply #4 on:
February 06, 2006, 11:23:25 PM »
Home Depot has stuff that you can make work.
Logged
Jim_Lusk
Official BS King
Global Moderator
BBD God
Offline
Posts: 5192
A-bodies since 1978, this one since 1983
Re: Are these easy to get???
«
Reply #5 on:
February 07, 2006, 01:03:42 AM »
Any parts store should have replacements.
Logged
7903 posts on old board.
mjudd
Full Member
Offline
Posts: 276
Springfield, Il.
Re: Are these easy to get???
«
Reply #6 on:
February 10, 2006, 09:25:17 AM »
http://cgi.ebay.com/ebaymotors/Mopar-66-69-383-426-HEMI-440-water-pump-nipples_W0QQcmdZViewItemQQcategoryZ34201QQitemZ4611440719QQrdZ1
parts stores are the cheapest route
Logged
middleagecrisis
Jr. Member
Offline
Posts: 25
BigBlockDart.Com
Re: Are these easy to get???
«
Reply #7 on:
February 10, 2006, 09:47:00 AM »
Quote from: mjudd on February 10, 2006, 09:25:17 AM
http://cgi.ebay.com/ebaymotors/Mopar-66-69-383-426-HEMI-440-water-pump-nipples_W0QQcmdZViewItemQQcategoryZ34201QQitemZ4611440719QQrdZ1
parts stores are the cheapest route
None of my local parts stores have the large heater hose fitting that goes into the intake (SB). Have any store names and part numbers for this piece?
Logged
jet-taz
Sr. Member
Offline
Posts: 809
BigBlockDart.Com
Re: Are these easy to get???
«
Reply #8 on:
February 17, 2006, 08:18:46 PM »
napa 660-1732. 5/8 hose 1'1/2 long 1/2 npt. napa 660-1734 3/4 hose 1'3/4. 1/2 npt hope that helps jet-taz
Logged
69 dodge dart/440 former god over 1200 post on old site
Pages:
[
1
]
Jump to:
Please select a destination:
-----------------------------
General Category
-----------------------------
=> Off-Topic
=> Wanted
-----------------------------
Technical
-----------------------------
=> Engine, Drivetrain
=> Chassis, Suspension
=> Body, Paint, Interior, Wiring
=> Early A-bodies
Author
Logged
tried and true
