Pages: [1] 
|
 |
|
 Author
|
Topic: Bulkhead elimination question. (Read 380 times)
|
69dartdrew
Jr. Member
 Offline
Posts: 20
BigBlockDart.Com
|
Hey guys. I'm sick of my electrical gremlins caused by my bulkhead connector. I've cleaned it, scrubbed it, and applied di-electric grease. but I've had it. How have you guys eliminated that connector? I am all for riveting on a piece of aluminum over the hole and drilling a hole for a large grommet to feed the wires thru. but what about the wires? solder them together or install a gm style connector? I'm not worried about maintaining any sort of originality. any help or photos would be greatly appreciated.  |
|
|
|
|
Logged
|
|
|
|
|
CudaDon65
|
I'm not sure this will help you but take a look at this..www.madelectrical.com.Good info.  |
|
|
|
|
Logged
|
|
|
|
69dartdrew
Jr. Member
Offline
Posts: 20
BigBlockDart.Com
|
I've performed the brighter headlight repair and the amp meter by-pass repair from the electrical tech. They have good advice, but didnt really address what I'm looking for. Thanks though. I recommend everyone read the electrical tech on that site.
|
|
|
|
|
Logged
|
|
|
|
|
68_Val_Sedan
|
|
|
|
|
|
Logged
|
67 dart 270 resto mod in progress ...
68 chrysler 300 wish it was my daily driver ...
|
|
|
Spook50
Full Member
Offline
Posts: 208
Yeah, I work on these
|
What I'd like to do is get a large cannon plug that threads together (like aircraft cannon plugs) for security, then have a seperate hole for the large gauge wire powering the dash equipment (after doing the ammeter elimination). I'm still keeping my eyes open, and I'll post up if I ever find anything.
|
|
|
|
|
Logged
|
BOOM shalock-lock boom...
|
|
|
Jim_Lusk
Official BS King
Global Moderator
BBD God
Offline
Posts: 4927
A-bodies since 1978, this one since 1983
|
The problem is the female ends opening up. This can be fixed by removing them one at a time and closing the gap a little. This is a lot less work than what you are talking about doing.
|
|
|
|
|
Logged
|
7903 posts on old board.
|
|
|
|
smallbigblock
|
Yea, I would like to use a plane bulkhead connector but don't know where to get them.
|
|
|
|
|
Logged
|
I should have left it alone
|
|
|
Spook50
Full Member
Offline
Posts: 208
Yeah, I work on these
|
Yea, I would like to use a plane bulkhead connector but don't know where to get them.
We've got a shit ton of different ones in what we call our "bench stock" (free-to-grab parts to just grab from the drawer when needed for a jet), but they all use way too small a wire gauge and don't have nearly enough "pins" to accomodate the number of wires that pass through the bulkheads on our Mopars. Not that it'd be exactly legal to just be swiping them for personal use anyway... |
|
|
|
|
Logged
|
BOOM shalock-lock boom...
|
|
|
|
nothingbutdarts
|
Yea, I would like to use a plane bulkhead connector but don't know where to get them.
We've got a shit ton of different ones in what we call our "bench stock" (free-to-grab parts to just grab from the drawer when needed for a jet), but they all use way too small a wire gauge and don't have nearly enough "pins" to accomodate the number of wires that pass through the bulkheads on our Mopars. Not that it'd be exactly legal to just be swiping them for personal use anyway... In the truck industry, they have 32 pin cannon plugs. Most manufacturers will use two or three pins at least for higher amperage circuits, example of all three wires feed the one power circuit and three more feed the ground side of the same circuit. |
|
|
|
|
Logged
|
69 Swinger 340
Soon to be 69 426 Dart
80 Crew Cab gas hawg
01 DIESEL Hauler
Bailey, Colorado
|
|
|
|
|
69dartdrew
Jr. Member
Offline
Posts: 20
BigBlockDart.Com
|
Had 7 volts going to my voltage regulator. had a huge voltage drop at the ignition wire terminal at the bulkhead. drilled out the terminal and ran a solid wire through there. now I've got 12.7 volts when its running at the voltage regulator. battery voltage 13.7v. Almost there. Only 1 more volt to free from the electrical goblins. Good stuff.  |
|
|
|
|
Logged
|
|
|
|
Spook50
Full Member
Offline
Posts: 208
Yeah, I work on these
|
Those things have been used and abused. I wouldn't touch 'em. |
|
|
|
|
Logged
|
BOOM shalock-lock boom...
|
|
|
|
west
|
I re did my wiring. I have no heater or wipers making it alot easier. i covered up the hole and put everything under the dash,now there is only one hole in the firewall for 6 wires. alt.,water temp,ign.,oil press.,starter and trans. there is another hole near the inner fender for the headlight wires.  |
|
|
|
|
Logged
|
|
|
|
|
Pages: [1] 
|
|
|
 |
