Pages: [1] 
|
 |
|
 Author
|
Topic: Quarter Panels- Who's Best? (Read 474 times)
|
wjaholic
Full Member
 Offline
Posts: 245
BigBlockDart.Com
|
I am going to replace a mess load of sheet metal on my Duster, Who has the best repop panels out there? Who is cheapest? Who Over charges for shipping? Year one? Paddock? Sherman?
|
|
|
|
|
Logged
|
“Give me a place to stand and a lever long enough and I will move the world.” - Archimedes
|
|
|
|
Lars
|
I don't know about quarters, but Auto body Speciaties was cheaper on shipping then the Paddock for my floor pan.
|
|
|
|
|
Logged
|
365/727/8.75 with 4.10's and a Detroit locker  |
|
|
|
Duster440
|
Kinda depends on where you live in relation to the supplier. Quarter skins are shipped by truck so you could pay $100-150 just for shipping. Although they may not have been my first choice, Layson's is a couple of hours from me so I drove over to them and picked it up. As far as who has the best stuff - most comes from the same place - Taiwan.
|
|
|
|
|
Logged
|
|
|
|
wjaholic
Full Member
Offline
Posts: 245
BigBlockDart.Com
|
That's a good idea about picking them up  . I will have to track down a distributor/supplier/retailer (whatever) in my area. How come no one makes repop b-posts? to complex? Not enough demand? Don't intend for the average hobbyist to replace something like that? This has always made me wonder  . [attachment deleted by admin] |
|
|
|
|
Logged
|
“Give me a place to stand and a lever long enough and I will move the world.” - Archimedes
|
|
|
|
signet
|
you will be able to fix that area up fine once the quarter is hacked back a bit.
|
|
|
|
|
Logged
|
|
|
|
|
Duster440
|
Looks pretty rough - particularly around the striker. I ended up replacing the jamb on the passenger side (had been wrecked and repaired but didn't look right) using a donor. Had a yard cut out the jamb all the way back past the outer wheel house. The donor qtr was worthless but I but I needed other stuff from the section. Lot's of spot welds to drill out.
|
|
|
|
|
Logged
|
|
|
|
|
Halfaed
|
You will find out that none of them fit too good. You just have to trim it and fit it to the car after you get your jam area fixed.  |
|
|
|
|
Logged
|
|
|
|
|
jimmyb
|
|
|
|
|
|
Logged
|
 Blown 572 Hemi Work in progrees Engine by Dram |
|
|
wjaholic
Full Member
Offline
Posts: 245
BigBlockDart.Com
|
Has anyone had a supplier/distributor bring your order to a show to meet you? Lets say that there is going to be a big drag race/ car show/ swap meet with a manufactures midway. And you knew that they (distrubtor/supplier) were going to be there so you call them up and order your parts and they take it with them to the show and you pick it up there? I had heard of this before but never had the opportunity to do it.
|
|
|
|
|
Logged
|
“Give me a place to stand and a lever long enough and I will move the world.” - Archimedes
|
|
|
|
Halfaed
|
I think they do that, I know glasstek has.
|
|
|
|
|
Logged
|
|
|
|
|
Pages: [1] 
|
|
|
 |
