Search Results - BigBlockDart.Com
BigBlockDart.com is the premier Dodge Dart Forum on the internet. Registered Users do not see the above ads.

Search:

Type: Posts; User: roccodart446

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    7
    Views
    2,370

    You can take a 73 and newer dash insert and use...

    You can take a 73 and newer dash insert and use that.

    Or take your stock dash and send it to Dakota digital. They will put a digital insert in your stock cluster.
  2. Replies
    2
    Views
    709

    I've always paid 150 to 200

    I've always paid 150 to 200
  3. Thread: 10in rim

    by roccodart446
    Replies
    3
    Views
    815

    You need 7.5" backspace to run a 10" wheel on a...

    You need 7.5" backspace to run a 10" wheel on a stock abody rear.

    You have to mini tub for this rim as well. The max section width that will go in a stock wheelhouse is 10.5" and that is tight.
  4. No, 3/4" offset hangers take an 8" wheel 69 or...

    No, 3/4" offset hangers take an 8" wheel

    69 or 71 take the same wheels
  5. Replies
    7
    Views
    2,370

    This is my peak dash

    This is my peak dash
  6. Replies
    5
    Views
    1,202

    I use type F

    I use type F
  7. Replies
    4
    Views
    1,118

    PPP shifter is tough to beat and fits the factory...

    PPP shifter is tough to beat and fits the factory console if you used one
  8. Replies
    23
    Views
    7,235

    Very nice car, love the color

    Very nice car, love the color
  9. Replies
    6
    Views
    2,253

    Circle track scales

    Circle track scales
  10. I'm not sure if you can tell in this picture but...

    I'm not sure if you can tell in this picture but I built a contoured tub with a flange so it could be simply dropped in and welded in place of the factory trunk floor.


    47602

    After doing this...
  11. Replies
    6
    Views
    2,488

    Why is this something to frown about? They are...

    Why is this something to frown about? They are dropping it and replacing it with what they are saying is a better tire with more choices within the selection. Given MT's track record and their...
  12. Replies
    127
    Views
    31,999

    yes, please update when that happens.

    yes, please update when that happens.
  13. Replies
    28
    Views
    8,651

    Crane Gold rockers are junk. Not to mention they...

    Crane Gold rockers are junk. Not to mention they had a recall a while back on their adjusters.

    I'd go with Harland Sharps myself. Never had a problem and they hold lash like nobody's business.
    ...
  14. Replies
    2
    Views
    965

    I had the blasted and powder coated.

    I had the blasted and powder coated.
  15. Replies
    127
    Views
    31,999

    I think I'm losing time on chassis extension. AKA...

    I think I'm losing time on chassis extension. AKA wasted motion. I have connectors. Your 60 ft. is faster than mine. I wonder if there is something I can do to reduce mine...
  16. Replies
    127
    Views
    31,999

    What is your rear suspension setup. My car goes...

    What is your rear suspension setup. My car goes 11.74 but yours seems to leave harder. What's you 60'? I notice the rear doesn't separate and you are pulling the front tire. Mine really separates on...
  17. Replies
    6
    Views
    1,910

    After having the 2" TTI's for a few years now I...

    After having the 2" TTI's for a few years now I wouldn't be too concerned with the starter trapping issue or the heat issue. . I have the Dakota aka mini starter. It is a little harder to swap in...
  18. Replies
    12
    Views
    2,875

    Unless you are looking for more out of an...

    Unless you are looking for more out of an existing cam I'd run 1:5's and have the cam cut to your desired spec.


    I've had the best luck with Harland sharp rockers. I would steer clear of crane...
  19. Replies
    3
    Views
    1,502

    I used the MPP offset adapter. You might as well...

    I used the MPP offset adapter. You might as well use it because it kills 2 birds with one stone.

    The master is a wilwood unit.
  20. Replies
    3
    Views
    1,157

    Yes, you can run 1:6 rockers but unless you need...

    Yes, you can run 1:6 rockers but unless you need the added lift for the head flow it's a waste.


    I'd recommend the Crane 684571.

    Hydraulic flat Tappet
    Duration 242/[email protected]
    .528/.552 lift...
  21. Replies
    3
    Views
    1,157

    I've used Dynamic, Art Carr and PTC with good...

    I've used Dynamic, Art Carr and PTC with good success. They have ranged from 3500-4000 stall.

    Gear for the street without an OD. I'd go 3:73 or 3:91.

    Cam: what style cam do you want? hyd,...
  22. Replies
    3
    Views
    1,502

    I use 7/8"

    I use 7/8"
  23. Replies
    9
    Views
    1,820

    My last 4 trucks have all been diesels. Everyone...

    My last 4 trucks have all been diesels. Everyone of them has over 200k on them. I would never go back to a gas truck, ever.
  24. Replies
    3
    Views
    1,040

    Is that one of the front 2 plugs on the passenger...

    Is that one of the front 2 plugs on the passenger side?
  25. #6

    #6
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4