Search Results - BigBlockDart.Com
BigBlockDart.com is the premier Dodge Dart Forum on the internet. Registered Users do not see the above ads.

Search:

Type: Posts; User: kendog170

Page 1 of 18 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    1
    Views
    576

    I'll assume the latch receiver is off and not...

    I'll assume the latch receiver is off and not pulling the trunk over while latching. If that's the case , loosen and slide it over. If not the case remove it and while the trunk is up push on the...
  2. Replies
    5
    Views
    1,057

    Finally got around to putting it on the car. I...

    Finally got around to putting it on the car. I installed the Decal and Painted the stripe. Still have the Trunk and other Quarter to do .
  3. Thread: TTI HEADERS

    by kendog170
    Replies
    3
    Views
    878

    I dropped my car over the engine,tranny bolted to...

    I dropped my car over the engine,tranny bolted to K frame suspension,starter,steering box and TTI's installed with no issues at all. I would not want to attempt with the engine in the car.
  4. Found one on Ebay. Been to busy to install. The...

    Found one on Ebay. Been to busy to install. The one in there is breaking and binding in the track.

    ...
  5. Replies
    30
    Views
    3,239

    Great news! Have fun

    Great news! Have fun
  6. Replies
    30
    Views
    3,239

    I would listen to HeyOldguy before listening to...

    I would listen to HeyOldguy before listening to me. But I do think a haed change may be in order. More info here.
    http://store.440source.com/Stroker-Kits/products/3/
  7. Replies
    30
    Views
    3,239

    Maybe these? I guess shims are for raising...

    Maybe these? I guess shims are for raising compression and used alone.

    https://www.summitracing.com/parts/cgt-c5460-098/overview/make/chrysler
  8. Replies
    30
    Views
    3,239

    I thought Mopar sold a shim to use with gasket?...

    I thought Mopar sold a shim to use with gasket? Not sure though.
  9. Replies
    30
    Views
    3,239

    Do what you gotta do but definitely go with max...

    Do what you gotta do but definitely go with max thickness gaskets what ever they may be.
  10. Replies
    30
    Views
    3,239

    I'm no expert but do you know your deck height?I...

    I'm no expert but do you know your deck height?I put together a 500 440 source 30 over stroker kit with 440 source heads I cant remember but believe I was .050 below deck flat tops Felpro gaskets . I...
  11. Replies
    12
    Views
    1,687

    I had a small block that was noisy on one side....

    I had a small block that was noisy on one side. Luckily I removed lifter galley plug and looked inside. Someone must off punched it in and put another plug in. Had a hard time removing it but got it...
  12. Replies
    7
    Views
    1,215

    Yes, I can't wait. Bought it in 1985 with a 110K...

    Yes, I can't wait. Bought it in 1985 with a 110K gave it a quick patch and paint. Freshened motor no machine work except valve job and timing chain. Took it off the road in 2001 rear main leaking on...
  13. Replies
    7
    Views
    1,215

    Couple of final install. Worked awesome.

    Couple of final install. Worked awesome.
  14. Yes that wasn't the issue. I think when I had my...

    Yes that wasn't the issue. I think when I had my motor and trans. bolted to the jig , the tail shaft was up higher than when in cars
    so it was pointing the starter down toward the steering by about...
  15. Replies
    12
    Views
    1,687

    I had some similar issues but not Roller cam just...

    I had some similar issues but not Roller cam just roller rockers .It was a Comp HL hydraulic cam. I bought a solid cam and lifter set but I never installed it's been 3 years car still runs great but...
  16. Dropped car over Engine , Trans. , Suspension install.

    I did this Saturday. Only took less than an hour. Still have to complete all the other stuff but couldn't t have gone smoother.
  17. Funny I install engine trans. suspension and now...

    Funny I install engine trans. suspension and now its all good. Kinda weird I know . I posted install picks on separate thread .
  18. It's just hitting the nut on the end of the...

    It's just hitting the nut on the end of the starter. Its the long bolt (one of two) that holds the winding on. Been busy with a couple of Northeasters here so I haven't been out in garage but will...
  19. Sorry guys I know it's a small block

    Sorry guys I know it's a small block
  20. Mini Denso 4379160 clearance issue question

    So my old starter was junk on my 68 340 Ragtop so I put a Denso mini starter in it that I had on the shelf . I am assembling the Engine and Trans. on the suspension. I had no issue at tear down...
  21. Replies
    7
    Views
    1,215

    Couple more pics. Manifolds and new 2 1/2" front...

    Couple more pics. Manifolds and new 2 1/2" front pipes on. Maybe install this weekend if weather permits.
  22. Replies
    7
    Views
    1,215

    I did it that way with my big block with headers...

    I did it that way with my big block with headers steering box, starter all installed. Took ten minutes to sock the four K member bolts and attach the trans. support bracket. No issues at all.
  23. Replies
    7
    Views
    1,215

    She's been sitting waiting !

    She's been sitting waiting !
  24. Replies
    7
    Views
    1,215

    Jig for Suspension,Motor and Trans.

    Finally got motor together so I welded up a jig from scrap metal from work so I can lower the car over the front drive train and suspension .
  25. No one ???????

    No one ???????
Results 1 to 25 of 442
Page 1 of 18 1 2 3 4