Search Results - BigBlockDart.Com
BigBlockDart.com is the premier Dodge Dart Forum on the internet. Registered Users do not see the above ads.

Search:

Type: Posts; User: valiant100

Page 1 of 8 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    3
    Views
    350

    Yeah, its no big deal. I did the same thing, ...

    Yeah, its no big deal. I did the same thing, dropped off my rods and crank to get re did. Your engine builder will just need your crank to set main bearing clearance. Maybe thats what he meant...
  2. Replies
    0
    Views
    333

    New V8 center link

    Firm Feel is making early a body V8 center links.
  3. Replies
    0
    Views
    636

    battery kill switch wiring

    I'm trying to find the best way to wire my battery disconnect switch. Seems like all the diagrams and drawings I see are all a little different. I have a Taylor 4 post switch and I want to use the...
  4. Replies
    7
    Views
    945

    From what ive read you can use 440 rods, but you...

    From what ive read you can use 440 rods, but you will need shorter stroker pistons. Just swapping the reground crank wont work.
  5. Replies
    12
    Views
    3,517

    I'm sorry, but this made my brain twitch.

    I'm sorry, but this made my brain twitch.
  6. Replies
    2
    Views
    736

    Just don't base your pinion angle relative to...

    Just don't base your pinion angle relative to your perches. Your springs hold the axle down a couple degrees already. This was something I totally overlooked. Put the rear end in with the perches...
  7. Replies
    15
    Views
    4,999

    Sincerely appreciate all the advice. Thanks

    Sincerely appreciate all the advice. Thanks
  8. Replies
    4
    Views
    1,597

    Can't you just scuff it up real good and spray...

    Can't you just scuff it up real good and spray over it?
  9. Replies
    15
    Views
    4,999

    It's primarily a bracket car, but street legal...

    It's primarily a bracket car, but street legal just so I can get it to the track. I had planned on getting one, but started second guessing... Thanks for the replys, I'll get one ordered.
  10. Replies
    15
    Views
    4,999

    Is a line lock necessary?

    I'm trying to get my brake lines finished, but I can't decide if I should install a line lock or not. I've had cars in the past that would break the tires loose without much effort, but never knew...
  11. valve cover height and adjustable rockers

    I just picked up some valve covers assuming they were "tall", but now i'm not so sure. They're Moroso stamped aluminum, and are 3" tall. They look like stock height but I don't have a stock one...
  12. Replies
    11
    Views
    3,227

    The pictures I've seen of adjustable strut rods...

    The pictures I've seen of adjustable strut rods used a heim joint.
  13. Replies
    2
    Views
    923

    The ones behind the headlights, and in front of...

    The ones behind the headlights, and in front of the door jams should be bolted in. Not sure about all years though...
  14. Replies
    5
    Views
    1,513

    Definitely not a job for the hammer, I had to...

    Definitely not a job for the hammer, I had to cut out a sizable chunk to make it fit.
  15. Replies
    5
    Views
    1,513

    I had the trans all bolted up in the cross...

    I had the trans all bolted up in the cross member. It's just when I lifted up on the front, it wouldnt get to level before it hit the floor. I just pulled it back out and I can sorta see where it...
  16. Replies
    5
    Views
    1,513

    440/727 in early A body ?'s

    So I just got a new AR motor plate, and with a little trimming, got it to fit nicely on the frame rails. Now i'm trying to get the trans in place so I know where to put the mounts for the motor...
  17. Thread: Paint Ideas

    by valiant100
    Replies
    13
    Views
    4,150

    I would look in to photo shop, or something...

    I would look in to photo shop, or something similar. I went through the same thing when trying to decide on a color.
  18. Replies
    20
    Views
    4,932

    There was a couple different size bolts for the...

    There was a couple different size bolts for the front spring hanger. Rear shackles should be easy to track down.
  19. Thread: 1978 Volare

    by valiant100
    Replies
    3
    Views
    2,089

    I just swapped belts and didn't bother to even...

    I just swapped belts and didn't bother to even look at the pulleys.
  20. Thread: 1978 Volare

    by valiant100
    Replies
    3
    Views
    2,089

    1978 Volare

    Picked up this beater a couple weeks ago for my daily driver. One of the issues is it has a very quick squeal/chirp when it shifts into 2nd, and a quick chirp on startup. The 1-2 shift is pretty...
  21. Replies
    3
    Views
    1,166

    The slip yoke at the trans is what im talking...

    The slip yoke at the trans is what im talking about.
  22. Replies
    3
    Views
    1,166

    727 transmission 1350 yoke

    How much power will a cast 1350 trans yoke safely handle, and when should you start considering forged, billet, chromoly etc. I almost ordered a Strange cast yoke #U1655, about $80. Then I...
  23. Replies
    11
    Views
    2,990

    doin some last minute shopping?

    doin some last minute shopping?
  24. Replies
    4
    Views
    1,253

    Are you talking about the ring gap...

    Are you talking about the ring gap...
  25. Light dust is no big deal. You just don't want...

    Light dust is no big deal. You just don't want big carbon chunks getting wedged in there. Use a shop vac first, not compressed air.
Results 1 to 25 of 185
Page 1 of 8 1 2 3 4