Search Results - BigBlockDart.Com
BigBlockDart.com is the premier Dodge Dart Forum on the internet. Registered Users do not see the above ads.

Search:

Type: Posts; User: 383man

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Thread: Mopar help

    by 383man
    Replies
    4
    Views
    1,294

    Isn't he asking for magazine subscripts and not...

    Isn't he asking for magazine subscripts and not internet places ? Ron
  2. Replies
    11
    Views
    1,653

    Here is a pic of it before I cut it as I have my...

    Here is a pic of it before I cut it as I have my middle part of the valley plate out in this pic because it hit the plate so I only had to cut what you see in the other pic. Ron
    ...
  3. Replies
    11
    Views
    1,653

    Cut the bottom of the intake exh crossover off....

    Cut the bottom of the intake exh crossover off. Its not an EGR passage its the exh cross over for eng warm up when it has a heat riser valve. But your heads have no heat passage's for the exh cross...
  4. Thread: A short video.

    by 383man
    Replies
    5
    Views
    1,597

    Thanks for the kind replies. Ron

    Thanks for the kind replies. Ron
  5. Thread: Mopar help

    by 383man
    Replies
    4
    Views
    1,294

    Then you want the mag "Mopar Collector Guide". ...

    Then you want the mag "Mopar Collector Guide". Ron
  6. Thread: A short video.

    by 383man
    Replies
    5
    Views
    1,597

    A short video.

    I found this video of me in my 63 and my brother in his Duster behind me leaving a local cruise spot. I found it by accident looking for a video of my friends car. Ron
    ...
  7. Replies
    5
    Views
    1,612

    Thats right as every car I put SS springs on sits...

    Thats right as every car I put SS springs on sits way crooked and I have to adjust the torsion bars a good bit to get the car level. Ron
  8. Replies
    5
    Views
    1,820

    As said they make more power then exh manifolds...

    As said they make more power then exh manifolds but not as much as a normal long tube header will. Ron
  9. Replies
    2
    Views
    836

    Actually none of the two wires going to the dist...

    Actually none of the two wires going to the dist pick-up coil have + current on them as the pick-up coil is almost what I would call a small generator as it creates its own current. You can use a...
  10. Thread: pick up coil??

    by 383man
    Replies
    6
    Views
    1,466

    Yes you can adjust them. Set the air gap on it at...

    Yes you can adjust them. Set the air gap on it at .008 using a brass feeler gauge. Ron
  11. Well I can tell you that my sons Dart you see...

    Well I can tell you that my sons Dart you see here is a 72 Dart with everything stock. The springs are in stock location and it has stock wheelwells. He is running 26 x 9.5 QTP Hoosier tires on a 15...
  12. Replies
    28
    Views
    8,271

    It sounds like a nice solid build you are working...

    It sounds like a nice solid build you are working up. The Trick Flow heads look like they are really going to work good. Myself I use Hughes roller tip rockers and I use a solid flat tappet cam. Its...
  13. Replies
    6
    Views
    1,880

    Well we have had CPPA (same as TTI) 2" headers on...

    Well we have had CPPA (same as TTI) 2" headers on my sons 400 Dart since 1997 and it still has the same V/6 starter on it that we used in 1997. Only thing I did was put some of the aluminum foil...
  14. Replies
    5
    Views
    2,189

    Right back at you and all the members. Ron

    Right back at you and all the members. Ron
  15. Replies
    8
    Views
    2,647

    I would say about the same. A few mild street...

    I would say about the same. A few mild street cars have run them and seem to get away with them but I hear many bad things about them also. I know I use Hughes roller tip rockers with my .592 lift...
  16. Sure the lash will make a difference. If you...

    Sure the lash will make a difference. If you check the cam specs off the lifter it should read just as the cam card says at >050 but when the eng is assembled with the valves adjusted at .018 then...
  17. Replies
    1
    Views
    783

    I use them in my eng. I run a custom grind solid...

    I use them in my eng. I run a custom grind solid flat tappet from Dwayne Porter and he supplied me the EDM lifters from Comp with the tiny hole in the bottom. I built my eng and put it in my 63 in...
  18. Replies
    12
    Views
    2,821

    I did finnaly talk to my brother and I found out...

    I did finnaly talk to my brother and I found out he has T & D rockers on his Victors and its because he bought them in a deal with the heads and you sure are not going to not use the T & D rockers if...
  19. Replies
    28
    Views
    8,271

    Well you cant go wrong following "qkcuda's" build...

    Well you cant go wrong following "qkcuda's" build as it runs strong. Myself I used a 440 block to make my 493 and I only used the 440 block because I felt I may want to put the crossram on it one...
  20. Replies
    11
    Views
    4,803

    Yea its looking real good. Ron

    Yea its looking real good. Ron
  21. Replies
    11
    Views
    4,803

    Yea uts looking real good. Ron

    Yea uts looking real good. Ron
  22. Replies
    113
    Views
    44,180

    I dont remember if I posted my sons Dart on here...

    I dont remember if I posted my sons Dart on here so here it is. Ron

    http://pic20.picturetrail.com/VOL1620/1011563/1886546/22948023.jpg
  23. Replies
    1
    Views
    1,080

    Right back at ya and thanks. Ron

    Right back at ya and thanks. Ron
  24. Replies
    16
    Views
    4,169

    Thanks again for all the kind replies. Ron

    Thanks again for all the kind replies. Ron
  25. Replies
    12
    Views
    2,821

    Well my Hughes rockers are not offset as they are...

    Well my Hughes rockers are not offset as they are on my EZ heads but they have held up awesome. My brother runs some Victor heads and another set of heads with offset rockers so I will get with him...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4