Search Results - BigBlockDart.Com
BigBlockDart.com is the premier Dodge Dart Forum on the internet. Registered Users do not see the above ads.

Search:

Type: Posts; User: smallbigblock

Page 1 of 10 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    1
    Views
    326

    Dumber Than I thought

    Well never mind I solved that by looking at the filler pipe. Stuff on the Pipe won't fit thru the hole (Vent, etc)
  2. Replies
    1
    Views
    326

    Gas Tank filler Neck question

    OK This might sound dumb to some of you guys, but I can't remember how the filler neck goes into the fuel tank. Does it go in from the outside the car, through the hole in the 1/4 pnl then into the...
  3. Replies
    1
    Views
    686

    I am looking for the same thing cause I did the...

    I am looking for the same thing cause I did the same thing

    I marked some of the plugs when I started removing them, but then for some reason I stopped marking the old ones. Now I am lost which...
  4. Replies
    2
    Views
    764

    Looks real good! I like how you did your mounts...

    Looks real good! I like how you did your mounts .... and the welding looks great.

    What brand radiator did you buy?
  5. Replies
    4
    Views
    684

    That's about where it ended up after messing...

    That's about where it ended up after messing around with it
  6. Replies
    4
    Views
    684

    Great. Thanks for the reply, I'll keep it...

    Great. Thanks for the reply, I'll keep it right near the bottom then
  7. Replies
    4
    Views
    684

    Need help with Oil Pickup clearance

    I'm test fitting my "187" oil pan and pickup tube. Can anyone tell me what the ideal clearance is between the bottom of the pan and the pickup tube. Right now if I where to bolt on the pan the non...
  8. Replies
    9
    Views
    2,298

    That a nice looking setup! I looked on the...

    That a nice looking setup!

    I looked on the mustang site but couldn't find the "Turnbuckel" adjuster thing, What did they call it?
  9. Go here and pick 67 Dart and that should give you...

    Go here and pick 67 Dart and that should give you the wiring diagram

    http://www.mymopar.com/index.php?pid=27
  10. Replies
    2
    Views
    479

    I mini tubed my 67 and ordered a complete stock...

    I mini tubed my 67 and ordered a complete stock SS e-brake kit and all worked fine. You do have to weld the rear bracket back on to the new spring boxes. You already knew that I bet
  11. I would love to see pictures! I plan on using...

    I would love to see pictures! I plan on using one but haven't figured out how to get every thing lined up
  12. Replies
    7
    Views
    759

    Yes. On this 67 I have since welded in 68 +...

    Yes. On this 67 I have since welded in 68 + brackets and run two tank straps (as per stock 68+). The 67 accross the frame got in the way of the springs when I moved them inboard. Sorry no pic's yet...
  13. Replies
    7
    Views
    759

    Here's a pic if it helps ...

    Here's a pic if it helps

    https://www.bigblockdart.com/forum/attachment.php?attachmentid=15167
  14. Replies
    2
    Views
    951

    Yes your right, If I can't find one I'll have to...

    Yes your right, If I can't find one I'll have to figure out how to make the brake light switch work.
  15. Replies
    2
    Views
    951

    Parking brake warning light switch

    Does anybody know were I can locate one of these. I had one but, now that I'm puting the car back together I can't locate it. Did a search on the internet ... seems like its a hard part to find.
    ...
  16. Replies
    2
    Views
    718

    Thanks, That's good to know.

    Thanks, That's good to know.
  17. Replies
    2
    Views
    718

    Compression Question

    I was reading info on dynamic compression. I found a Chevy article that was well written, but was wondering if their opinions applied to Mopar stuff.

    They said that a dynamic compression between...
  18. Replies
    8
    Views
    1,121

    I was wondering if there was some mistake but I...

    I was wondering if there was some mistake but I couldn't find any good info on the part numbers
  19. Replies
    8
    Views
    1,121

    Head Gasket Confusion??

    Does anybody know what the difference between these MP gaskets are?

    How can a steel shim gasket cost $160.

    https://www.bigblockdart.com/forum/attachment.php?attachmentid=13771
  20. Replies
    1
    Views
    484

    Help with new Fuel tank pad

    Well I got my new tank and Tank pad today and was looking at them and I realized that I'm not sure where the pad should be located on the tank. My original tank did not have a pad.
    ...
  21. Replies
    4
    Views
    893

    What wieght is everyone using?? I bought...

    What wieght is everyone using??

    I bought 75W-90 but I am not sure which is best.
  22. Thanks for the info. It seems like we are...

    Thanks for the info.

    It seems like we are always worried about nuts or bolt backing off on every other part of the drive train, and these are not self locking nuts....how the hell do they stay...
  23. Getting Ready put my Rear-end together for first time

    Getting set to put everything together and I was wondering about using thread locker on both the carrier and axle flange nuts. What everyone else doing?? I read the shop mannual and it's not...
  24. I love the Magnums

    I love the Magnums
  25. Here is a pic ...

    Here is a pic

    https://www.bigblockdart.com/forum/attachment.php?attachmentid=12063
Results 1 to 25 of 231
Page 1 of 10 1 2 3 4