Search Results - BigBlockDart.Com
BigBlockDart.com is the premier Dodge Dart Forum on the internet. Registered Users do not see the above ads.

Search:

Type: Posts; User: my64dart

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    1
    Views
    126

    Hi, I'm using the Lokar engine oil dipstick....

    Hi,
    I'm using the Lokar engine oil dipstick. It's pretty flexible, but kinda hard to read. It's probably the only one that would work with my setup.
  2. Replies
    1
    Views
    186

    Quick Fuel Brawler BR-67258

    So I picked up this Quick Fuel Brawler BR-67258 Out of the box setup, the exhaust was very rich smelling. So after doing some research and messing around I got it dialed in pretty close. The idle...
  3. Replies
    2
    Views
    554

    Let's keep this strictly a Mopar forum. ...

    Let's keep this strictly a Mopar forum.
    Thank You
  4. Replies
    3
    Views
    553

    To be on the safe side, I would get the HP...

    To be on the safe side, I would get the HP manifolds. I have a pair on my 64 Dart because it's a very narrow car. I still needed to install a double universal joint to get around the steering shaft. ...
  5. Replies
    2
    Views
    543

    Hi, Check out Rock Auto. They have a few...

    Hi,
    Check out Rock Auto. They have a few molded hoses for a 1968 Dart with a big block. You can get the part numbers and then order it locally if you want to. If it doesn't fit you can just...
  6. Replies
    13
    Views
    1,835

    OK, Good Luck. We spend to much money on all...

    OK, Good Luck. We spend to much money on all these parts and end up having to modify them in the end.
  7. Replies
    13
    Views
    1,835

    Hi, Have you tried to put the wheels on the...

    Hi,
    Have you tried to put the wheels on the car yet? I've heard you need 15'' rims to clear the calipers. Small bolt pattern is 14'' rim I think. I'm not sure if this is correct or not.
  8. Thread: Hello

    by my64dart
    Replies
    4
    Views
    748

    Welcome aboard! Glad to see some new Mopar folks...

    Welcome aboard! Glad to see some new Mopar folks on here. Check out the tech pages for some useful information.
  9. Replies
    5
    Views
    896

    Welcome back!

    Welcome back!
  10. Thread: Hello to all

    by my64dart
    Replies
    1
    Views
    278

    Welcome to the BBD

    Welcome to the BBD
  11. Replies
    11
    Views
    4,496

    Hi, This is an old post ,but worth bringing up...

    Hi,
    This is an old post ,but worth bringing up again. There are some aftermarket water pump housings on the market that are inadequate to keep your big block cool. They are forged with a...
  12. Replies
    2
    Views
    1,017

    Hi, My Dart has a rubber boot between the...

    Hi,
    My Dart has a rubber boot between the pitman arm and centerlink. You can buy replacements from Summit Racing or Jeg's. There made by Energy Suspension. Good luck trying to figure out which...
  13. Thread: TTI HEADERS

    by my64dart
    Replies
    3
    Views
    1,154

    Welcome to the world of A Body Mopars. Everytime...

    Welcome to the world of A Body Mopars. Everytime I work on my Dart it's a pain in the ass. Good luck. You'll get it done eventually.
  14. Replies
    6
    Views
    1,467

    Hi, This is actually a great place to start....

    Hi,
    This is actually a great place to start. By putting the tires and rims your going to use, exactly where you want them to be underneath the car. This means you'll be right on the money for how...
  15. Replies
    6
    Views
    1,467

    Hi, When I narrowed my 8.75 Mopar rear end, I...

    Hi,
    When I narrowed my 8.75 Mopar rear end, I went to stock measurements for an A-body. I wasn't quite sure what I was doing either. I wish I would have make it a little narrower so a larger tire...
  16. Replies
    30
    Views
    3,834

    Hi, Rule #1 / Don't beat on your Mopar if...

    Hi,
    Rule #1 / Don't beat on your Mopar if the streets are wet, unless you want to total it. Why don't you just drive it and have some fun. If it's running good, leave it alone.
  17. Replies
    30
    Views
    3,834

    Hi, Heyoldguy is right. Don't those heads and...

    Hi,
    Heyoldguy is right. Don't those heads and everything that go with them cost about $3,000.00 Keep them and get the right pistons.
  18. Replies
    30
    Views
    3,834

    Hi, Give 440source a call. Tell him what you...

    Hi,
    Give 440source a call. Tell him what you have. Their suppose to be the stroker experts. I'm sure he will help straighten out all these questions about pistons & heads & compression.
  19. Replies
    30
    Views
    3,834

    Hi, I got to agree with heyoldguy. You will...

    Hi,
    I got to agree with heyoldguy. You will change the way everything fits by adding thicker gaskets. The best solution would probably be to get the proper pistons to get the compression down to...
  20. Replies
    30
    Views
    3,834

    Hi. Wow, your having the worst luck with that...

    Hi.
    Wow, your having the worst luck with that engine you picked up. It seems you have a lot of good parts, but there not matched for what you want to do. Maybe you should give up on that block...
  21. Replies
    30
    Views
    3,834

    Hi, I don't know anything about Indy Heads...

    Hi,
    I don't know anything about Indy Heads so this might sound stupid. But can't you just get rid of them and put some Edelbrook Performer heads on you engine. With a 84cc or 88cc chamber size....
  22. Thread: Camshaft help

    by my64dart
    Replies
    1
    Views
    787

    Hi, With all the different camshaft companies...

    Hi,
    With all the different camshaft companies out there, and choices, are you looking for a hydraulic, solid,or roller cam? I went with a Lunati Voodoo cam. It's a hydraulic, flat tappet cam....
  23. Hi, I see that they sell header collector...

    Hi,
    I see that they sell header collector reducers in a ball and socket style. Looks like you can adjust the pipe in any direction you want. Would something like that help with your clearance...
  24. Replies
    12
    Views
    2,121

    Hi, The reason I stated to use a heavier oil...

    Hi,
    The reason I stated to use a heavier oil is because if the lifters are bad, and bleeding down to fast your gonna get that lifter noise. The heavier oil will help quiet it down a bit. I bought...
  25. Replies
    12
    Views
    2,121

    Hi, Why don't you try a heavier oil. Go to a...

    Hi,
    Why don't you try a heavier oil. Go to a 40w or 50w oil and see if that helps. I've had bad luck with a certain major brand oil company and won't use them again. Just try a different brand...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4